Korg Nautilus Control for Android - Help

Thank you for Installing the APP. If you have any questions or suggestions, please contact us via email: pedrocoelho.ti@gmail.com

This APP's main purpose is to facilitate real-time control of the Korg Nautilus when playing live.

Please Test the limited version thoroughly before purchasing the full version. In the limited version it is possible to control up to 3 channels and the application disconnects after half an hour.

Read the instructions below to make good use of the APP

Important points:

· The APP is compatible with Android 6 or higher operating system, but depending on the hardware of your device, the APP may not work correctly

· Use a high quality communication cable.

· Always use DUMP transfer from the keyboard, as it is faster and avoids inconsistencies.

· The SETLIST, COMBINATION and PROGRAM settings are the keyboard's factory default settings.

· Disable Developer mode on Android device to avoid USB port conflicts.

Android Limitations

· The Android Operating System has difficulty transmitting large MIDI SYSEX data packets and depending on the capacity of your Android Device , transmissions may generate some inconsistencies.

In normal real-time control operations, no errors were observed.

Using the APP

Initial setting

· Disable Developer mode on Android device and close any other midi App to avoid USB port conflicts.

· Connect the cable to the USB output of the Keyboard and the Android device. The CONNECTED message will be displayed on the APP.

· Access the keyboard in MODE-GLOBAL -> PAGE-MIDI and change the options:

o Midi Clock: Internal.

o MIDI Filter : enable all options. All of them are recommended.

o MIDI Routing Setup: X-Y Control

Initial Charge

1. Access MODE-GLOBAL -> PAGE-MIDI.

2. Click on the top right menu .

3. Dump Program : Select which programs you want to sync and click ok to continue.

4. Even after the keyboard signals complete, wait a few seconds for the APP to finish recording the data.

5. Repeat steps 2, 3 and 4 for Dump Combination and Dump Set list .

If you select multiple banks, it is recommended to perform the same operation more than once.

When you want to synchronize only one Setlist or Combination, use the Get Current Comb and Get Current Setlist options in the Main Menu.

App superior Menu

· SET LIST: Selects SetList Page

· COMBINATION: Selects the Combination page

· CONTROLS: Selects Control Screens in Real Time

· Comment : Shows or hides comments from the Setlist Slot

·  M: App main menu access APP

App Main Menu

· Get Current Comb : Brings the current combination data that is loaded in real time to the APP. Whenever you update the combination on the keyboard, perform this operation. · Get Current Setlist : Brings data from the current Setlist that is loaded in real time to the APP. Whenever you update a setlist on the keyboard, perform this operation · Rotate 180: Rotates the screen by 180% · Sync Options : Opens the sync options screen. Use the keyboard to be more efficient. · Settings: General APP Settings

Configuration Screen (Settings)

· Display only used channels on Mixer : If enabled,only channels that are in use will be displayed on the mixer .

· Use large Solo/ Mute button on Tablet: If enabled, it will display large mute and solo buttonsfor easier clicking.

· Control only Mute/Solo on Combination screen: If enabled, não exibe os volumes no mixer

· Display Controls on Combination Screen when possible : If enabled, will attempt to display the controls on the same Mixer screen .

· Controls Size Percent ( 50 to 100): Increases or decreases the size of the controls.

Carry out several tests to arrive at the best configuration for your case.

SetList selection

To select the Setlist , click the Change Setlist button on the SET LIST page and the screen below will be displayed.

Click on the desired Setlist to load it on the Set List page

Release Setlist

On this screen, you can select the Setlist by clicking on the desired slot. If it is a combination, the combination will be loaded on the COMBINATION page.

The Comment button will display the SLOT comment

Combination Page – Mode 01

Buttons 1< and >16 are used to change the mixer between the first and last channel.

Combination Page – Mode 02

Combination Page – Mode 03

Control Page – Simple to use (It Controls Arp and X-Y)